Home & Garden

Can you wire 2 4ohm subs to 2 ohms?

By: Zeinab RahimiUpdated: January 03, 2021

Categories

Site Statistics

  • Questions
    94,481
  • Answers
    1,984,101
  • Categories
    21
  • Last Updated
    September 26, 2022
Subwoofer manufacturers make subs with dual voice coils (DVC) to take advantage of this difference in wiring schemes, so the user has more freedom of system design. A DVC 4-ohm sub can be wired into a system as a 2-ohm or as an 8-ohm load. A DVC 2-ohm sub can have a total impedance of 1 ohm or 4 ohms.

Besides, what hits harder 2ohm or 4ohm?

A subwoofer with a lower electrical resistance produces a louder sound than one with a high electrical resistance, which means that 2ohm subwoofers are louder than 4ohm ones. Although louder, 2 ohm subwoofers are also more likely to produce a poorer quality of sound due to its' power consumption.

Additionally, is it better to wire subs in series or parallel?

When speakers or voice coils are wired in series, you add their impedances together to find their total impedance. Two 4-ohm speakers wired in series have a total impedance of 8 ohms. When speakers or coils are wired in parallel, however, the formula for their total impedance is more complicated.

Is 1 ohm bad for an amp?

if an amp is designed to be 1 ohm stable, then its ok. running an amp not designed to do it can/will end up bad. there are some amps that can do . 5 ohm, and a very few that can do .

Can a 2 ohm amp run a 1 ohm sub?

Your 1 ohm sub will draw twice as much current as your 2 ohm amp can deliver, which will kill it. Is it a dual voice coil sub? You can wire it for higher impedances if it is. if you only run one sub coil the sub will only have half of its power handling.

Related

Can you wire a 4 ohm speaker to 2 ohms?

If you take 4 ohm speaker and wire it in parallel with a 4 ohm resistor you WILL get 2 ohms of total resistance. However, your speaker will still get the same amount of power and all the additional power created by dropping the ohm load will go to the resistor and be turned to heat.

Can you wire 2 Ohm DVC subs to 2 ohms?

Subwoofer manufacturers make subs with dual voice coils (DVC) to take advantage of this difference in wiring schemes, so the user has more freedom of system design. A DVC 4-ohm sub can be wired into a system as a 2-ohm or as an 8-ohm load. A DVC 2-ohm sub can have a total impedance of 1 ohm or 4 ohms.

Is 2ohm or 4ohm better?

Basically, a 2 ohm subwoofer demands less power from the amp and tends to deliver louder bass. On the contrary, a 4 ohm subwoofer will demand more power from the amp and deliver less loud but higher quality bass. Thus, make your choice depending on the kind of bass you want.

Does bridging AMP lower ohms?

When you bridge an amp the ohm rating does not change. You can only change the ohms by wiring speakers differently(series or parallel). When you bridge an amp it typically won't be 2ohms stable, most are only 4ohms stable when bridged.

Can you run two subs off a mono amp?

Most mono amplifiers are designed to run at 2 ohms; some are even 1-ohm stable. A: The benefits of hooking up two subs to a mono amplifier are the same as hooking up any other number of subs to a mono amp: you can push the subs with more power at lower impedances.

What's the difference between 1 ohm and 2 ohm?

1 ohm or two ohm makes absolutely no difference, it simply depends on what load the amplifier was designed for, what the amp circuits were optimized for. Everything else being equal, an amp built for and running in 1 - ohm will behave exactly the same as an amp designed for and running in 2 - ohms.

What amp do I need for my 2 12 subs?

RMS, and RMS only with anything car audio. secondly, the amp can be a little under, but you will suffer as far as sound quality goes. 400 watts RMS per sub, that'd 800, so 150% (optimal) would be 1200 watts. 1200 watts (RMS) is what you want in an amp, look for that.

What is a 1 ohm stable amp?

At 1-ohm, this amp will be capable of powering 1-channel at a constant 750-watts over one channel, 550-watts at 2-ohm over one channel, or 400-watts at 4-ohm over one channel. This means you'll be able to completely optimize your individual sound system, depending on how you want it to be set up.

What sounds better 1ohm or 4ohm?

If you want it to sound best AND you want the system to last longer, you want to run a sub at 4 ohm. The ONLY reason to run a 1 ohm load is when you simply can't afford an amplifier that will give necessary power at a 4 ohm load.

What Does bridging an amp mean?

Bridging an amplifier refers to the process of combining two of four channels into one or two channels with half the ohms. At 4 ohms, it may be able to push out as much as about 200 watts into a single channel when bridged. This is a highly versatile way of powering a subwoofer.